troubleshooting:replication
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| troubleshooting:replication [2019/04/16 01:04] – Scott Cunliffe | troubleshooting:replication [2025/01/21 22:07] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 8: | Line 8: | ||
| * [[troubleshooting: | * [[troubleshooting: | ||
| - | * | + | * [[troubleshooting: |
| + | |||
| - | --> | ||
| - | Replication previously set up and running | ||
| - | Is the master server running | ||
| - | --> Yes | ||
| - | Is the replicant server running | ||
| - | --> Yes | ||
| - | Are the ports used by the master and replicant open and listening | ||
| - | --> Yes | ||
| - | <-- | ||
| - | --> No | ||
| - | Have your network staff open the required ports for inbound and outbound communications | ||
| - | <-- | ||
| - | --> Not sure | ||
| - | --> Checking master to replicant port access | ||
| - | <-- | ||
| - | --> Checking replicant to master port access | ||
| - | <note tip>The following commands are using default install values. | ||
| - | Stop the replicant server. | ||
| - | Open config file, comment out replicant section and save file | ||
| - | restart server in foreground mode, using the command in an administrative command line window | ||
| - | <sxh> | ||
| - | TMSS10Server -f -h " | ||
| - | </ | ||
| - | Open another administrative command line window and execute the command | ||
| - | <sxh> | ||
| - | netstat -na | find " | ||
| - | </ | ||
| - | to check that the port is actively listening. | ||
| - | <sxh> | ||
| - | netstat -na | find " | ||
| - | | ||
| - | </ | ||
| - | From the master server run the command TMSS10Ping with the replicant server address and port. | ||
| - | --> Connection successful | ||
| - | <-- | ||
| - | --> Connection unsuccessful | ||
| - | Have your network staff open the port | ||
| - | <-- | ||
| - | <-- | ||
| - | <-- | ||
| - | <-- | ||
| - | --> No | ||
| - | Restart the replicant server using the Framework Server Helper, administrative command line or windows services | ||
| - | <-- | ||
| - | <-- | ||
| - | --> No | ||
| - | <-- | ||
| - | --> Not sure | ||
| - | From an administrative command line window on the master server run the command TMSS10Ping | ||
| - | --> Connection Successful | ||
| - | From an administrative command line window on the replicant server run the command TMSS10Ping | ||
| - | --> Connection Successful | ||
| - | <-- | ||
| - | --> Connection Unsuccessful | ||
| - | <-- | ||
| - | <-- | ||
| - | --> Connection Unsuccessful | ||
| - | Restart the master server using the Framework Server Helper, administrative command line or windows services | ||
| - | <-- | ||
| - | <-- | ||
| - | <-- | ||
| - | --> Replication not previously set up | ||
| - | Replication setup attempted | ||
| - | --> Yes | ||
| - | Replicant Server started first | ||
| - | --> Yes | ||
| - | Master Server started after Replicant server | ||
| - | --> Yes | ||
| - | <-- | ||
| - | --> No | ||
| - | Start Master server | ||
| - | <-- | ||
| - | <-- | ||
| - | --> No | ||
| - | Stop replicant server and Master server, follow instructions for [[server: | ||
| - | <-- | ||
| - | <-- | ||
| - | --> No | ||
| - | Follow instructions for [[server: | ||
| - | <-- | ||
| - | <-- | ||
troubleshooting/replication.1555376655.txt.gz · Last modified: 2025/01/21 22:07 (external edit)